Documents › 61c8fcfaabe8b9b5ec965444f8f05cea6c8983dd:38-43
Ventura PD Crash Data Retrieval Report GO# VE 2019-90723
About this document
- Layer
- agency record: part of a file an agency produced
- Type as titled
- general offense report (kind from doc_type)
- Produced as
- ventura-police-department/ROOT/GOVE_2019-90723_Redacted.pdf
- File
- 61c8fcfaabe8b9b5ec965444f8f05cea6c8983dd application/pdf
- Cases
About: Gabrielle Root (case)
Page 2 · file page 39
larger image
Text: OCR
figure: some text describes an image
Figure: the OCR model's description, not text on the pageVentura Police Department logo
VENTURA POLICE DEPARTMENT
GENERAL OFFENSE HARDCOPY
PRA
GO# VE 2019-90723
5401-1 TRAFFIC- HIT & RUN- NO INJURY
Figure: the OCR model's description, not text on the pageBosch logo
20-2229
Figure: the OCR model's description, not text on the pageCDR CRASH DATA RETRIEVAL logo
EDR Data Elements Overview/Interpretation in CDR Report:
Under CDR File Information Section
- • Event(s) recovered indicates if an event was detected and recorded by RCM. If no event is detected, it will indicate "none". If a trigger or non airbag deployment event is detected, it will indicate "unlocked event". If an airbag deployment is detected, it will indicate "locked frontal event", or "locked side event", or "locked rollover event".
Under System Status at Event Section
- • Complete file recorded indicates if data from the recorded event has been fully written to the RCM memory.
- • If the RCM detected a peripheral crash sensor was lost during an event, the crash sensor would be identified as well as the time it was lost during that event relative to Time zero. If no loss of a peripheral crash sensor, nothing would be displayed. Note in some vehicles, loss of a peripheral crash sensor may lead to the loss of another peripheral crash sensor due to shared communication.
Under Deployment Data Section
- • If the RCM commanded a deployment during an event, the deployment device(s) would be identified as well as the time the RCM commanded its deployment relative to Time zero. If no device was commanded to deploy by the RCM, nothing (no deployment device (s)) would be displayed.
Under Pre-Crash Data -5 to 0 sec
- • Steering Wheel Angle if Applicable: positive value indicates left turn, and negative value would indicate right turn.
- • Stability Control Lateral Acceleration if Applicable: Lateral Acceleration (Y-direction) is the acceleration along the lateral axis of the vehicle, reported as positive when accelerating to the left.
- • Stability Control Longitudinal Acceleration if Applicable: Longitudinal Acceleration (X-direction) is the acceleration along the longitudinal axis of the vehicle, reported as positive when accelerating in a forward direction.
- • Stability Control Yaw Rate if Applicable: The Yaw Axis is the vertical axis of the vehicle, generally perpendicular to the plane of the road. A positive Yaw Rate is counter-clockwise when observing the vehicle from above.
- • Stability Control Roll Rate if Applicable: The Roll Axis is the longitudinal axis of the vehicle, generally aligned with the primary axis of motion of the vehicle. A positive Roll Rate is counter-clockwise when observing the vehicle from the front.
Under Longitudinal Crash Pulse
- • Delta-V_longitudinal: SAE J211 sign convention, negative value generally indicates a front crash and positive value generally indicates a rear crash. Longitudinal delta-V reflects the change in forward velocity that the sensing system experienced from Time zero. It is not the speed the vehicle was traveling before the event. Note that the vehicle speed is recorded separately. This data should be examined in conjunction with other available physical evidence from the vehicle and scene when assessing occupant or vehicle longitudinal delta-V.
Under Lateral Crash Pulse
- • Delta-V_lateral: SAE J211 sign convention. Positive value generally indicates a driver side crash and negative value generally indicates a passenger side crash.
Under Rollover Sensor Data (if Applicable)
- • Vehicle roll angle if applicable: The Roll Axis is the longitudinal axis of the vehicle, generally aligned with the primary axis of motion of the vehicle. A positive Roll Angle is counter-clockwise when observing the vehicle from the front.
Data Sources:
The Restraints Control Module (RCM) contains all recorded data on any event. Data collected from the RCM comes from multiple sources:
-
- Internal to the RCM such as internal sensors for delta Velocity data, rollover angle data if applicable, etc... which are measured, calculated and stored internally.
-
- External to the RCM but with a direct connection such as buckle switches, peripheral crash sensors, seat track switch(s) etc... which are measured, calculated and stored internally.
-
- External Modules to the RCM such as Powertrain Control Module, Brake Control Module, etc... These modules communicate to the RCM via Vehicle Communication Network. The RCM stores the received data internally.
02013_RCM-RC7P_r001
Keys: ← → or j k turn pages; / finds.